• Large capacity for storing 60,000 data points • Lowpass Filter will filter out the harmonics • LED flickers when the preset current value is exceeded • CALL:Confirmation of recorded data • Selection of One-time mode or Endless mode • Non Volatile Memory • Battery power indicator • The userfriendly PC software "KEW LOG Soft 2" is supplied • Continuous measuring time:Approx. 10 days (Alkaline Battery)
3 channel inputs for the simultaneous recording of Leakage Current, Load Current and Voltage
Large Capacity for storing 60,000 data points
60,000 data points can be recorded when 1ch is used, and when all the three channels are used, 20,000 data points per channel can be recorded
Lowpass Filter will filter out the harmonics (Cutoff Frequency = Approx. 160Hz)
LED flickers when the preset current value is exceeded
CALL: Confirmation of recorded data
The following can be displayed: number of recorded data points, (max+ min+ peak) value for each channel complete with time/date information in the Normal recording mode. (Detected values (i.e. when values are outside preset limits ) can be displayed in other recording modes)
RECALL: The last 10 recorded data points including time/date can be recalled on the logger display
Selection of One-time mode or Endless mode
One-time on: Recording will stop when memory is used up
One-time off: Overwrite the old data, and store the latest data
Non Volatile Memory Recorded data will be retained even if the batteries are exhausted or replaced due to the presence of a nonvolatile memory (guaranteed for 10 years)
Battery power indicator Indicates battery voltage in 4-levels (It is possible to use the logger for a further approx. 24 hours even after the warming symbol is flashing)
The userfriendly PC software "KEW LOG Soft 2" is supplied
Supplied with the user friendly software "KEW LOG Soft 2". This permits editing, analysis and graphical display of data.
The recorded data is downloadable onto a PC via USB cable.
Continuous measuring time: Approx. 10 days (Alkaline Battery)
Normal Recording Mode (AC 50/60Hz, Sine wave, Input: 10% or more of the range at CH1)
±2.0%rdg±0.9%f.s.+ Accuracy of Sensor
±1.5%rdg±0.7%f.s.+ Accuracy of Sensor
2.5 or less: RMS accuracy (sine) + 2%rdg + 1%f.s.
*Max, Min and Instant Peak values in Normal Recording mode are just reference values: their accuracies aren't guaranteed.
Trigger Recording Mode (AC 50/60Hz sine wave)
±3.5%rdg±2.2%f.s.+ Accuracy of Sensor
±3.0%rdg±2.0%f.s.+ Accuracy of Sensor
Capture Recording Mode
±3.0%rdg±1.7%f.s.+ Accuracy of Sensor
±2.5%rdg±1.5%f.s.+ Accuracy of Sensor
Normal, Trigger, Capture
Successive Approximation (CH1 single synchronized sampling)
Rated max. working voltage
AC 9.9Vrms, 14V peak value
Number of input channel
RMS measuring interval
Normal/Trigger mode : approx. 1.65ms/CH Capture mode : approx. 0.55ms (waveform: at every 1.1ms)
Low battery warning
Battery mark display (in 4 levels)
"OL" mark is displayed when exceeding the measuring range
Auto power off
Power-off function operates automatically after a switch remains for 3min. (when recording is stopped)
OBIAT Electronics Pty Ltd | Test & Measurement Equipment
OBIAT Electronics has been established as an importer, distributor, wholesaler and retailer of quality Test and Measuring Instruments for over fifteen years.
Our competent staff collectively have over forty years of experience in electrical and electronic testing and are well qualified to offer the right advice and applications support for our customers equipment needs.
We provide service and calibration support and have a competent network of sub-distributors throughout Australia. If you have a requirement for Test and Measuring Instruments don't waste your time and money. Talk to us first and last!