Sartorius - Moisture Analyser | Mark3 HP

Read more...

To contact Sartorius Australia about Sartorius Moisture Analyser | Mark3 HP use Get a quote.

Its high-resolution weighing system also makes the Mark 3 HP suitable for precisely analyzing the moisture and water content of very dry samples. This feature makes it a genuine alternative to Karl-Fisher titration.

Mark 3 HP Moisture Analyzer with printer, consisting of:

• LMA100PA-000U control module incl. printer
• LMA100PQ-000U heater module (0.1 mg, 100 g)
• optional on request: Moisture Analysis individual Service (YMD01P)

Advantages

• Economical and reliable alternative to the Karl-Fischer titration and drying oven methods
• Intuitive operation – With a learning curve of a few minutes
• The user starts the measurement by pressing just one button
• Robust and fast, optimal for routine operation
• Multi-module operation enables parallel measurements of up to 4 different samples on one single device
• An extensive range of security settings guarantees reliable results and 100% traceability

Specifications

• Data Printer: Thermal printer, built-in
• Built-in Calibration Weight: Yes
• Data Interface: Serial
• Dimensions (W×D×H): 41.3 × 49.5 × 23.5 cm
• Features
  • Analysis Mode: Timer mode, when value falls below a defined weight loss per time unit (%/min), trend shutoff
  • Display: Quarter VGA with contrast adjustment (black on white or white on black), Sealed membrane keypad with audible tactile feedback
  • Display Mode for Results: Weight, % Moisture, % Solids, % Volatiles, PPM moisture, PPM drying mass
  • Heating Mode: Standard test, Syringe, "Splash" method or Concentration modes, programmable temperature steps, one or two with selectable ramp rate
  • Maximum Number of Programs: 300
  • Memory Data Storage: 999 individual results with statistics: average, SD, RSD, high and low
  • Password Protection: Yes
  • Readability: 0.1 mg, 0.001%
  • Sample IDs: Yes
  • reproTEST: Built in reproTEST for determining the repeatability of the weighing system
• Maximum Weighing Capacity: 100g
• Recommended Moisture Range: Recommended Moisture Range
• Line Voltage: 90–250 VAC 50/60 Hz self-adjusting power supply
• Accuracy of the Weighing System: +/- 0.1 mg
• Additional Product Specifications
  • Modular configuration: Control and Heater modules (Optional: up to 4 heater modules)
  • Temperature adjustment: Optional fixture for internal electronic two-point adjustment
  • Temperature display: Display of both target and current temp at each stage of testing and standby
  • Conserve mode clock: Programmable time by day of week to shut down and wake up analyzer
  • Balance module design: Monolithic weighing cell with protective stainless steel cover
  • Ideal weight: Audio and visual signal when ideal weight is reached
  • Target limit alert: Minimum and maximum programmable limits and screen alert when test done
  • Operator names: Twenty alphanumeric operator names
  • Graph mode: Graph of temperature and percentage over time
• Heating Source: Thermogravimetric, loss on drying, Heat Source: Four parallel infrared quartz cylinders
• Temperature Range: 30°C – 210° C in one-degree increments/RTD sensor, +/- 1° C, Standby temperature selectable from 30°C – 160°C
• Typical Reproducibility of Weighing System
  • Starting at an initial sample weight of approximately 1 g: ± 0.1%
  • Starting at an initial sample weight of approximately 5 g: ± 0.02%
• Weight (approximate): 10 kg

By sending an enquiry to Sartorius you confirm that you have read the Declaration of Consent (found in downloadable content) regarding the data processing for marketing purposes by Sartorius and consent to this processing.

Read less...

To contact Sartorius Australia about Sartorius Moisture Analyser | Mark3 HP use Get a quote.