4 Post Car Hoist | 5000Kg HAPP27-27W

4 Post Car Hoist | 5000Kg HAPP27-27W Price Guide: $5,800

Supplier: HAPP Australia

4 Post Car Hoist | 5000Kg HAPP27-27W

1/6

This is the latest of our range that has successfully passed Australian Standards compliance. Ready to go in to any Workshop. Certified to 5T. Please call our team on 0439 833 497 as we are not affiliated with Industry Search & don't get your email.

These hoists are typically $9,000 for similar or lesser quality. We can provide installers in most States or assist you on the initial installations. A comprehensive installation and operation manual has been prepared by HAPP that details all the installation and operation of the hoist.

These hoists are extremely enduring.

The wheel alignment kit is an option, $1800 at 24.2.25

All internal welds are inspected by external quality assurance engineers before powder coating.

Features:

Single point safety release control all four columns simultaneously
Cross beam 130mm 10mm I beam
Runway – 3 x 100mm 10mm C section beams under checker plate
Columns – 5 mm thickness
Base plate – 16mm
Industrial strength load ramp and end plates
Slave runway is movable allowing for narrow and extra wide vehicles
Plastic powder coat finish
Ultra strong frame and columns
Full Australian engineering structural analysis & design
Australian standards approved and WH&S registered
Full WH&S maintenance program available with WH&S kit
Release all column safeties, raise and lower from single point
Ratchet safety at with 150mm increments
Max runway height 1940mm
Lockout pins for extended vehicle storage
Removable 855mm on ramps
HAPP ultra strong 12.5mm thick all steel lift cables tested in NATA registered lab.
Tru-bolt anchor bolts for solid mounting
High steel grade rugged construction – a) 5mm column, b) 127mm I beam cross beam, c) 3x120mm C section beams under each runway d) Checker plate runway surface e) Approved cable / cylinder / safety system
Connector to external limit switch on motor
Access to HAPP customer group buy plan

Specifications:

Load Capacity – 5000kgs
Lifting Height – 200-1940mm
Overall Height – 2277mm
Overall Width – 2855-3400mm
Overall Length – 5100mm
Width between pillars – 3148mm
Drive through – 2748mm
Ramp length – 855mm
Min pad height 150mm
Rise/Drop time: <50sec/>20sec
Net weight – 1296kg
Packed measurements: 510cm x 113cm x 23cm
CE approved Hydraulic Power Pack
Motor Capacity – 240V, Single phase or 3 Phase 415V (3 phase is an additional $150.00)
Power of motor – 2.2kw
15 amp plug supplied

Note:

HAPP hoists come standard with steel oil containers where included, Plastic containers as shown can be provided if so desired.

All HAPP hoists have ratchet safety latches in the columns, users only work with vehicles when the mechanical safety latches are engaged allowing safe work at any lift height.

To contact HAPP Australia about 4 Post Car Hoist | 5000Kg HAPP27-27W use Get a quote.

These hoists are extremely enduring.

The wheel alignment kit is an option, $1800 at 24.2.25

All internal welds are inspected by external quality assurance engineers before powder coating.

Features:

Single point safety release control all four columns simultaneously
Cross beam 130mm 10mm I beam
Runway – 3 x 100mm 10mm C section beams under checker plate
Columns – 5 mm thickness
Base plate – 16mm
Industrial strength load ramp and end plates
Slave runway is movable allowing for narrow and extra wide vehicles
Plastic powder coat finish
Ultra strong frame and columns
Full Australian engineering structural analysis & design
Australian standards approved and WH&S registered
Full WH&S maintenance program available with WH&S kit
Release all column safeties, raise and lower from single point
Ratchet safety at with 150mm increments
Max runway height 1940mm
Lockout pins for extended vehicle storage
Removable 855mm on ramps
HAPP ultra strong 12.5mm thick all steel lift cables tested in NATA registered lab.
Tru-bolt anchor bolts for solid mounting
High steel grade rugged construction – a) 5mm column, b) 127mm I beam cross beam, c) 3x120mm C section beams under each runway d) Checker plate runway surface e) Approved cable / cylinder / safety system
Connector to external limit switch on motor
Access to HAPP customer group buy plan

Specifications:

Load Capacity – 5000kgs
Lifting Height – 200-1940mm
Overall Height – 2277mm
Overall Width – 2855-3400mm
Overall Length – 5100mm
Width between pillars – 3148mm
Drive through – 2748mm
Ramp length – 855mm
Min pad height 150mm
Rise/Drop time: <50sec/>20sec
Net weight – 1296kg
Packed measurements: 510cm x 113cm x 23cm
CE approved Hydraulic Power Pack
Motor Capacity – 240V, Single phase or 3 Phase 415V (3 phase is an additional $150.00)
Power of motor – 2.2kw
15 amp plug supplied

Note:

HAPP hoists come standard with steel oil containers where included, Plastic containers as shown can be provided if so desired.

All HAPP hoists have ratchet safety latches in the columns, users only work with vehicles when the mechanical safety latches are engaged allowing safe work at any lift height.

Read less...

To contact HAPP Australia about 4 Post Car Hoist | 5000Kg HAPP27-27W use Get a quote.

HAPP27W(0.22MB)

HAPP27(0.22MB)

Happ Sept_2025 catalogue(2.87MB)

AI Overview BETA

The HAPP27-27W is a four-post vehicle hoist designed to raise cars and other vehicles for workshop servicing and repair work. A single-point release controls the safety locks on all four columns at once, so operators release them from one control. Automotive workshops can add the optional wheel-alignment kit when configuring the hoist for vehicle alignment work.