Maric | Wafer Type Flow Control Valves | ...

Maric | Wafer Type Flow Control Valves | Stainless Steel ANSI/ASME

Supplier: Maric Flow Control Australia

The Stainless Steel ANSI/ASME is designed for mounting between ANSI 150 and ANSI 300 pipe flanges.

20 Recent Views Call for more details

Features:

Materials: Body- 316 Stainless Steel to ASTM484/A276. Sealing O’Rings - Nitrile, potable water approved to AS4020 or EPDM or Viton if applicable
Flange Specification: Suits ANSI flanges (ASME/ANSI B16.5) Alternative specs are available - Refer to Valve Selection Guide. Standard Wafers are not full flange type i.e. flange bolts locate wafer concentrically and remain visible when viewing assembly. Wafers are fitted with an o’ring in each face for sealing against smooth flat faced flanges. Gaskets will however be required where grooved, raised or rough cast face flanges are used. PVC and Poly Stub Flanges note; Due to smaller I.D. of these flanges/pipes, optional spacers are often required to prevent restriction.
Max Pressure Differential: 2000 kPa (for N7 & E7 rubbers Only)
Max Hydrostatic Pressure: 6000 kPa
Max Temperature: 60C for Nitrile control rubbers - 100C for EPDM - 200C for Viton
Compatible Control Rubbers: Standard Precision P (Non Standard LP, N6, N7, EP, E7, V, HF)

To contact Maric Flow Control Australia about Maric | Wafer Type Flow Control Valves | Stainless Steel ANSI/ASME use Get a quote.

Features:

Materials: Body- 316 Stainless Steel to ASTM484/A276. Sealing O’Rings - Nitrile, potable water approved to AS4020 or EPDM or Viton if applicable
Flange Specification: Suits ANSI flanges (ASME/ANSI B16.5) Alternative specs are available - Refer to Valve Selection Guide. Standard Wafers are not full flange type i.e. flange bolts locate wafer concentrically and remain visible when viewing assembly. Wafers are fitted with an o’ring in each face for sealing against smooth flat faced flanges. Gaskets will however be required where grooved, raised or rough cast face flanges are used. PVC and Poly Stub Flanges note; Due to smaller I.D. of these flanges/pipes, optional spacers are often required to prevent restriction.
Max Pressure Differential: 2000 kPa (for N7 & E7 rubbers Only)
Max Hydrostatic Pressure: 6000 kPa
Max Temperature: 60C for Nitrile control rubbers - 100C for EPDM - 200C for Viton
Compatible Control Rubbers: Standard Precision P (Non Standard LP, N6, N7, EP, E7, V, HF)

Read less...

To contact Maric Flow Control Australia about Maric | Wafer Type Flow Control Valves | Stainless Steel ANSI/ASME use Get a quote.

AI Overview BETA

Maric’s stainless steel ANSI/ASME wafer-type flow control valve fits between ANSI 150 and ANSI 300 pipe flanges, with bolts locating the wafer concentrically. O-rings on each face seal against smooth, flat-faced flanges, so those assemblies do not require separate gaskets. PVC and Poly Stub Flanges often require optional spacers to prevent restriction from their smaller internal diameters.

316 stainless steel body to ASTM484/A276
Maximum pressure differential: 2,000 kPa for N7 and E7 rubbers only
Maximum hydrostatic pressure: 6,000 kPa
Maximum temperatures: 60°C for Nitrile and 100°C for EPDM
Viton rubber: maximum temperature 200°C

Source: listing by Maric Flow Control Australia on IndustrySearch · Updated 5 Nov 2026

AI Overview is generated by artificial intelligence and may contain mistakes.

Let Maric Flow Control Australia provide you with a quote