Huntron PCB Fault Finding Tool Tracker ...

Huntron - PCB Fault Finding Tool Tracker 3200S

Supplier: Metromatics

PCB Testing Tool

Tracker 3200S with board attached

1/2

The Huntron Tracker 3200S is a test and troubleshooting solution for PCB Circuit Boards. It allows power off testing of the electronic circuit. Therefore, preventing any further damage.

Video for Huntron PCB Fault Finding Tool Tracker 3200S

Testing Tool prevents damage to PCBs

6 weeks+ (Accepting orders)

The Huntron Tracker 3200S provides a powerful test and troubleshooting solution for PCB Circuit Boards. It is the perfect Circuit Board Fault Finding Tool as it allows a power off test of the electronic circuit – thereby, preventing any further damage.

The Tracker 3200S features a variable range parameters resulting in hundreds of voltage, source resistance & frequency combination. You can create Tracker ranges to precisely fit your needs.

Colour LCD Touch Screen for control of features
Fast refresh rate for screening component pins & displays A & B Channel signatures at the same time
Built in pulse generator to allow testing of gated devices as SCRs, TRIACs & relays

The Tracker 3200S features two 64 pin IDC connectors (one per channel) where custom cable interfaces can be used to quickly scan PCB connectors as a type of “first pass” test. If signature differences are detected then you can trace the connector pin to the component level saving you troubleshooting time. The two 64 pin connectors can be combined for a total of 128 pins and you have the ability to select any pin to be used as Common. You can also use standard IC clips and cables to easily scan standard ICs and select SOICs. Clip and cables are available from places such as Digi-Key.

Automate your test with Access Prober

The Tracker 3200S is designed to connect to a Huntron Access Prober for full diagnostic automation. BNC connections on the rear panel allow you to easily interface the Huntron Access, Access 2 or Access DH Probers. If you need to test high density, surface mount PCBs, robotic automation is a tremendous time saver.

Therefore, Tracker users have their preferred range settings. Hence, Tracker 3200S can save four range combinations that you use the most. Select on the touch screen display (buttons 1-4). The LCD also displays current ranges settings, pulse generator settings, current selected pin, SigAssist calculated values (resistance, capacitance, power, forward and reverse diode breakdown voltages), A vs. B comparison tolerance and Pass/Fail indication.

Tracker 3200S Features

Add the benefits of Power-Off test to your current diagnostic test strategy
Match the circuit impedance by setting the applied voltage, frequency and source resistance
Built-in Pulse Generator for testing gated devices such as relays, SCRs and TRIACs
128 pin scanning with 128 Commons using the built-in front panel IDC ribbon cable connectors
Display A or B channels individually, in the switching ALT mode or in A+B mode to display both signatures at the same time
Connect to a Huntron Access Prober for full test automation
Use the Huntron Workstation software to create circuit board tests, store analog (V-I) signatures, make good vs. bad comparisons and present the results
Having the Good board signatures stored on your PC eliminates the need to keep one for direct comparison
A software based test allows for the sharing of board test knowledge with all personnel

Technical Specifications

Part Number	99-0432
Number of Voltages plus values	24 voltages: 200mV, 400mV, 600mV, 800mV, 1V to 20V in 1V steps including 10V (Low), 15V (Med 1), 20V (Med 2)
Number of Resistances plus values	16 resistances: 10Ω, 20Ω, 50Ω, 100Ω, 200Ω, 500Ω, 1kΩ, 2kΩ, 5kΩ, 10kΩ, 20kΩ, 50kΩ, 100kΩ, 54Ω (Low), 1.2kΩ (Med 1), 26.7kΩ (Med 2)* * Through Huntron Workstation only
Number of Frequencies plus values	40 frequencies: 20Hz to 190Hz in 10Hz steps; 200Hz to 1.9kHz in 100Hz steps; 2kHz to 5kHz in 1kHz steps
Range Selection	Stand alone mode: Front panel push buttons and preset LCD buttons Remote Mode: Controlled by Huntron Workstation
Display	Colour TFT LCD with Touch screen; LED back light
Pulse Generator	Level: 0 to +/- 10V DC or Square wave; Pulse mode width: 2% to 50% duty cycle; Source Resistance: 100Ω; Maximum current: 100mA per channel
Front Panel Connections	Banana jacks for A/B Test channels and Common Banana jacks for Pulse Generator outputs (G1, G2) Two 64 pin IDC connectors (can be combined for 128 pins) with selectable Common pin for use with PCB interface cables or IC clips
Rear Panel Connections	BNC connectors for A/B Test channels and Common (used to interface to Access Prober); AUX connector for Footswitch accessory (included)

Automate your test with Access Prober

Tracker 3200S Features

Add the benefits of Power-Off test to your current diagnostic test strategy
Match the circuit impedance by setting the applied voltage, frequency and source resistance
Built-in Pulse Generator for testing gated devices such as relays, SCRs and TRIACs
128 pin scanning with 128 Commons using the built-in front panel IDC ribbon cable connectors
Display A or B channels individually, in the switching ALT mode or in A+B mode to display both signatures at the same time
Connect to a Huntron Access Prober for full test automation
Use the Huntron Workstation software to create circuit board tests, store analog (V-I) signatures, make good vs. bad comparisons and present the results
Having the Good board signatures stored on your PC eliminates the need to keep one for direct comparison
A software based test allows for the sharing of board test knowledge with all personnel

Technical Specifications

Part Number	99-0432
Number of Voltages plus values	24 voltages: 200mV, 400mV, 600mV, 800mV, 1V to 20V in 1V steps including 10V (Low), 15V (Med 1), 20V (Med 2)
Number of Resistances plus values	16 resistances: 10Ω, 20Ω, 50Ω, 100Ω, 200Ω, 500Ω, 1kΩ, 2kΩ, 5kΩ, 10kΩ, 20kΩ, 50kΩ, 100kΩ, 54Ω (Low), 1.2kΩ (Med 1), 26.7kΩ (Med 2)* * Through Huntron Workstation only
Number of Frequencies plus values	40 frequencies: 20Hz to 190Hz in 10Hz steps; 200Hz to 1.9kHz in 100Hz steps; 2kHz to 5kHz in 1kHz steps
Range Selection	Stand alone mode: Front panel push buttons and preset LCD buttons Remote Mode: Controlled by Huntron Workstation
Display	Colour TFT LCD with Touch screen; LED back light
Pulse Generator	Level: 0 to +/- 10V DC or Square wave; Pulse mode width: 2% to 50% duty cycle; Source Resistance: 100Ω; Maximum current: 100mA per channel
Front Panel Connections	Banana jacks for A/B Test channels and Common Banana jacks for Pulse Generator outputs (G1, G2) Two 64 pin IDC connectors (can be combined for 128 pins) with selectable Common pin for use with PCB interface cables or IC clips
Rear Panel Connections	BNC connectors for A/B Test channels and Common (used to interface to Access Prober); AUX connector for Footswitch accessory (included)

Read less...

To contact Metromatics about Huntron PCB Fault Finding Tool Tracker 3200S use Get a quote.

PCB Fault Finding Tool Tracker 3200S(8.08MB)

Let Metromatics provide you with a quote

Supplier

Supplier: Metromatics

Distribution: Australia & New Zealand

Location: North Lakes, QLD

Customers: Raytheon Australia, BAE Systems, Boeing Australia, QR, Transgrid, Snowy Hydro, SAAB, ASC

Trade With Confidence. The supplier of this item is approved as a Verified Supplier. Business registration, contact details and locations have been verified. Metromatics are also proudly displaying these credentials:

Established:

1989

Employees:

21-50

Customers:

Raytheon Australia, BAE Systems, Boeing Australia, QR, Transgrid, Snowy Hydro, SAAB, ASC

Certifications:

ISO 9001: 2015

Distribution:

Australia & New Zealand

Location:

North Lakes , QLD