Sigra Field Data Logger | V10

Sigra - Field Data Logger | V10

Supplier: Sigra

Field Data Logger | V10

Sigra’s newest V10 field data logger may be used to collect and transmit data from a variety of sensors and devices.

In Stock

Applications for this product

Landslide or excavation monitoring
Groundwater monitoring

Features of this product

The loggers will directly read many kinds of transducer including those with voltage or frequency outputs, vibrating wire transducers or resistance devices.
Multi-logger setups (supporting additional transducers) can be interconnected via an RS485 bus. These loggers can additionally be setup in a master slave configuration and take readings in turn.
Windows based software allows the setup and downloading of the data logger via any communications interface.
The Sigra Data Logger V10 comes with a 32 GB micro-SD card built-in to permit lifetime storage.
The internal clock chip with a built-in crystal oscillator has a time drift of less than 2 minutes a year across the full operating temperature range. Less than 20 seconds of drift is achievable if maintained between 10 and 40 degrees Celsius.
The V10 Data Logger (IP65 version) now has a built-in Low Voltage Disconnect (LVD) to protect the batteries from extreme discharge. This prevents the early failure of cells.

Specifications of this product

8 Channels for Voltage, Resistance and Frequency.
4 may be used for Vibrating Wire (Odd Channels).
4 may be used for Counting Inputs (Even channels).
Vibrating Wire: Range: 0.5 – 5 kHz; Resolution: 0.01 Hz; Raw unit: 0.1 Hz
Resistance: Range: 0 – 330 k?; Resolution: 1 ?; Raw unit: 1 ?
Voltage: Range: 0 – 5 V (Use an external potential divider for higher voltages); Resolution: 77 µV (16 bit); Raw unit: 77 µV
Radio: Frequency: 2.4 GHz ISM Band or 920 MHz; Transmit Power: 63mW and 250 mW respectively; Reliable range: 0.6 km and 2.5 km respectively – dependent on local conditions and topography
DIN Mounting: IP20
Weatherproof enclosure: IP65

To contact Sigra about Sigra Field Data Logger | V10 use Get a quote.

Applications for this product

Landslide or excavation monitoring
Groundwater monitoring

Features of this product

The loggers will directly read many kinds of transducer including those with voltage or frequency outputs, vibrating wire transducers or resistance devices.
Multi-logger setups (supporting additional transducers) can be interconnected via an RS485 bus. These loggers can additionally be setup in a master slave configuration and take readings in turn.
Windows based software allows the setup and downloading of the data logger via any communications interface.
The Sigra Data Logger V10 comes with a 32 GB micro-SD card built-in to permit lifetime storage.
The internal clock chip with a built-in crystal oscillator has a time drift of less than 2 minutes a year across the full operating temperature range. Less than 20 seconds of drift is achievable if maintained between 10 and 40 degrees Celsius.
The V10 Data Logger (IP65 version) now has a built-in Low Voltage Disconnect (LVD) to protect the batteries from extreme discharge. This prevents the early failure of cells.

Specifications of this product

8 Channels for Voltage, Resistance and Frequency.
4 may be used for Vibrating Wire (Odd Channels).
4 may be used for Counting Inputs (Even channels).
Vibrating Wire: Range: 0.5 – 5 kHz; Resolution: 0.01 Hz; Raw unit: 0.1 Hz
Resistance: Range: 0 – 330 k?; Resolution: 1 ?; Raw unit: 1 ?
Voltage: Range: 0 – 5 V (Use an external potential divider for higher voltages); Resolution: 77 µV (16 bit); Raw unit: 77 µV
Radio: Frequency: 2.4 GHz ISM Band or 920 MHz; Transmit Power: 63mW and 250 mW respectively; Reliable range: 0.6 km and 2.5 km respectively – dependent on local conditions and topography
DIN Mounting: IP20
Weatherproof enclosure: IP65

Read less...

To contact Sigra about Sigra Field Data Logger | V10 use Get a quote.

AI Overview BETA

The Sigra V10 is a field data logger that collects and transmits readings from a range of sensors and devices. It directly reads transducers with voltage or frequency outputs, vibrating-wire transducers and resistance devices, bringing several sensor types into one logger. The logger suits landslide or excavation monitoring and groundwater monitoring, with eight channels for voltage, resistance and frequency inputs.

RS485 links multi-logger setups; master-slave units take readings in turn
Windows software configures and downloads data through any communications interface
IP65 version includes low-voltage disconnect to protect batteries from extreme discharge
Clock drift stays below 2 minutes a year over the operating temperature range
Odd channels support vibrating-wire transducers; even channels serve as counting inputs

Source: listing by Sigra on IndustrySearch · Updated 1 Nov 2026

AI Overview is generated by artificial intelligence and may contain mistakes.

Let Sigra provide you with a quote