HMPS Rotary Tub and Cup Filling Machines

HMPS - Rotary Tub and Cup Filling Machines

Supplier: HMPS

Rotary Tub and Cup Filling Machines

1/6

Australian-made HMPS rotary tub and cup filling machines denest, fill, foil, seal, lid and eject on one carousel, with single, double and triple lanes producing up to 120 tubs per minute.

Australian made

Specifications

Specification	Standard
Typical output	Up to 40 tubs/min single lane, up to 80 double lane, up to 120 triple lane
Index rate	Up to 35–40 index/min, regardless of lane count
Container range	Height 35–135 mm, diameter Ø77–Ø127 mm, volume 50–1,000 ml, round containers
Stations	8 standard (dispense, fill, foil place and spot seal, heat seal, over cap, lid tamp, eject, one open station); 12-station configurations available
Filling	Volumetric piston standard (80 mm bore covers the full range), plus nett weight, gravity/level, pump, multihead weigher and dry dosing
Particulates	Up to a 12 mm cube
Sealing	Pre-cut foil place and spot seal, then heat seal at a dedicated station; snap lid placed and tamped. Foil only or lid only both available
Changeover	Approximately 10 minutes; change parts specific to each tub and foil size
Construction	Stainless throughout — SS316 product contact, SS304 structural, plus PEEK, PTFE, acetal and UHMW
Hygiene	Full washdown capability; manual clean standard with automatic CIP a priced upgrade; HEPA clean-fill, cup and foil sterilisation available
Controls	Allen Bradley CompactLogix, PanelView Plus, PowerFlex 525, AB VPL servos, SEW Eurodrive, IFM sensors
Power / air	415V AC 3-phase 50Hz + N + E, 20A per system · 6 bar, 350 L/min clean dry air
Safety & standards	Category 3 minimum, Category 4 compressed air · AS4024 guarding · AS3000 wiring
Footprint	Single lane 2,217 × 1,378 × 1,990 mm · triple lane 2,066 × 2,066 × 1,990 mm

Features

Australian made, with robust engineering.
Denests, fills, seals, lids and ejects around one indexing carousel. Throughput scales by lanes rather than speed; product viscosity and fill volume affect achievable output.
Product-specific station allocation supports two-stage layered filling, settling, inspection and missing-tub detection. Two fill stations increase filling speed at the same accuracy.
Separate dry dosing with a volumetric shuttle handles inclusions; layered filling uses a base dose followed by a main dose, with settling between.
Dedicated foil placing, spot sealing, heat sealing, lid dispensing and tamping stations provide a consistent tamper-evident seal.
Filling stations support automatic CIP with manifolds, butterfly valves and a return pump. Dry dosing stations are not CIP-able.
Optional HEPA-filtered air covers filling stations inside enclosed guarding; cup and foil sterilisation modules are available.
Change parts include the cup magazine, foil magazine and locators. The auto cup loader has a counter for quick, repeatable size changes.
Specifications depend on product and environment.

Applications

Layered yoghurt and mousse; fruit syrup bases; nuts and dry inclusions; dairy desserts.
Greek and stirred yoghurt; yoghurt with fruit; mixed confectionery inclusions.
Dips, spreads, coleslaw and prepared salads.
Cream, ice cream and soup.

Specifications

Specification	Standard
Typical output	Up to 40 tubs/min single lane, up to 80 double lane, up to 120 triple lane
Index rate	Up to 35–40 index/min, regardless of lane count
Container range	Height 35–135 mm, diameter Ø77–Ø127 mm, volume 50–1,000 ml, round containers
Stations	8 standard (dispense, fill, foil place and spot seal, heat seal, over cap, lid tamp, eject, one open station); 12-station configurations available
Filling	Volumetric piston standard (80 mm bore covers the full range), plus nett weight, gravity/level, pump, multihead weigher and dry dosing
Particulates	Up to a 12 mm cube
Sealing	Pre-cut foil place and spot seal, then heat seal at a dedicated station; snap lid placed and tamped. Foil only or lid only both available
Changeover	Approximately 10 minutes; change parts specific to each tub and foil size
Construction	Stainless throughout — SS316 product contact, SS304 structural, plus PEEK, PTFE, acetal and UHMW
Hygiene	Full washdown capability; manual clean standard with automatic CIP a priced upgrade; HEPA clean-fill, cup and foil sterilisation available
Controls	Allen Bradley CompactLogix, PanelView Plus, PowerFlex 525, AB VPL servos, SEW Eurodrive, IFM sensors
Power / air	415V AC 3-phase 50Hz + N + E, 20A per system · 6 bar, 350 L/min clean dry air
Safety & standards	Category 3 minimum, Category 4 compressed air · AS4024 guarding · AS3000 wiring
Footprint	Single lane 2,217 × 1,378 × 1,990 mm · triple lane 2,066 × 2,066 × 1,990 mm

Features

Australian made, with robust engineering.
Denests, fills, seals, lids and ejects around one indexing carousel. Throughput scales by lanes rather than speed; product viscosity and fill volume affect achievable output.
Product-specific station allocation supports two-stage layered filling, settling, inspection and missing-tub detection. Two fill stations increase filling speed at the same accuracy.
Separate dry dosing with a volumetric shuttle handles inclusions; layered filling uses a base dose followed by a main dose, with settling between.
Dedicated foil placing, spot sealing, heat sealing, lid dispensing and tamping stations provide a consistent tamper-evident seal.
Filling stations support automatic CIP with manifolds, butterfly valves and a return pump. Dry dosing stations are not CIP-able.
Optional HEPA-filtered air covers filling stations inside enclosed guarding; cup and foil sterilisation modules are available.
Change parts include the cup magazine, foil magazine and locators. The auto cup loader has a counter for quick, repeatable size changes.
Specifications depend on product and environment.

Applications

Layered yoghurt and mousse; fruit syrup bases; nuts and dry inclusions; dairy desserts.
Greek and stirred yoghurt; yoghurt with fruit; mixed confectionery inclusions.
Dips, spreads, coleslaw and prepared salads.
Cream, ice cream and soup.

Read less...

To contact HMPS about HMPS Rotary Tub and Cup Filling Machines use Get a quote.

Let HMPS provide you with a quote

Supplier

Supplier: HMPS

Distribution: Australia & New Zealand

Location: ADELAIDE AIRPORT, SA

Customers: Asahi, Bega, BWX, Mondelez, Ingham, McCain, Mars, Linfox, Unilever, Coles, Fonterra, Heinz

Trade With Confidence. The supplier of this item is approved as a Verified Supplier. Business registration, contact details and locations have been verified. HMPS are also proudly displaying these credentials:

Established:

1980

Employees:

51-200

Customers:

Asahi, Bega, BWX, Mondelez, Ingham, McCain, Mars, Linfox, Unilever, Coles, Fonterra, Heinz

Distribution:

Australia & New Zealand

Location:

ADELAIDE AIRPORT , SA

Joined:

Nov 2026