Wittmann Blow Air Chiller
Wittmann - Blow Air Chiller
Supplier: Wittmann Battenfeld
Blow Air Chiller
The Blow Air Chiller (BAC) is our top performer in internal mold cooling: powerful and equipped with the FIT controller to get the most out of your system.
Description
Documents
In Stock
Product Features:
- The Blow Air Chiller (BAC) is our top performer in internal mold cooling: powerful and equipped with the FIT controller to get the most out of your system.
- The compressed air is cooled down to -35 °C in the BAC – this requires good quality compressed air.
- A residual oil content of maximum 0.01 mg/m3 and a maximum pressure dew point of 5 °C at 7 bar are an important prerequisite to avoid problems, as oil would destroy the molecular sieve in the PAD.
- The adsorbent serves to lower the dew point of the compressed air far enough to prevent freezing of the moisture in the system.
- With optimum quality compressed air, you can take advantage of the maximum benefits of internal mold cooling!
Material & Workmanship:
- Outer housing made of brushed stainless steel
- High quality refrigeration compressor
- Fully insulated internals to prevent sweat
- Crane hook
- Water- and oil separators to clean the compressed air
- Activated carbon filter to also remove chemical residues
Product Benefits:
- One of the most critical and at the same time the most lengthy sub-process in extrusion blow molding is the cooling of the plastic parts, as the temperature gradient between the cold water-cooled outside and the warmer inside causes material stress. This degrades the quality and can lead to failure in leak, load and/or drop tests. Therefore, a system to chill with cold compressed air from the inside has been developed for many years, the Internal Air Cooling System (IACS).
- This increases productivity by up to 200% while helping to improve the quality of the products by exchanging cold air inside of the blow moulded product during the cooling phase. This ensures that material stress is reduced and the cooling time is automatically reduced. In most cases, material savings of up to 10% were achieved. The payback periods, according to our experiences, are between two weeks and six months.
To contact Wittmann Battenfeld about Wittmann Blow Air Chiller use Get a quote.
Product Features:
- The Blow Air Chiller (BAC) is our top performer in internal mold cooling: powerful and equipped with the FIT controller to get the most out of your system.
- The compressed air is cooled down to -35 °C in the BAC – this requires good quality compressed air.
- A residual oil content of maximum 0.01 mg/m3 and a maximum pressure dew point of 5 °C at 7 bar are an important prerequisite to avoid problems, as oil would destroy the molecular sieve in the PAD.
- The adsorbent serves to lower the dew point of the compressed air far enough to prevent freezing of the moisture in the system.
- With optimum quality compressed air, you can take advantage of the maximum benefits of internal mold cooling!
Material & Workmanship:
- Outer housing made of brushed stainless steel
- High quality refrigeration compressor
- Fully insulated internals to prevent sweat
- Crane hook
- Water- and oil separators to clean the compressed air
- Activated carbon filter to also remove chemical residues
Product Benefits:
- One of the most critical and at the same time the most lengthy sub-process in extrusion blow molding is the cooling of the plastic parts, as the temperature gradient between the cold water-cooled outside and the warmer inside causes material stress. This degrades the quality and can lead to failure in leak, load and/or drop tests. Therefore, a system to chill with cold compressed air from the inside has been developed for many years, the Internal Air Cooling System (IACS).
- This increases productivity by up to 200% while helping to improve the quality of the products by exchanging cold air inside of the blow moulded product during the cooling phase. This ensures that material stress is reduced and the cooling time is automatically reduced. In most cases, material savings of up to 10% were achieved. The payback periods, according to our experiences, are between two weeks and six months.
To contact Wittmann Battenfeld about Wittmann Blow Air Chiller use Get a quote.
Get a quote
Let Wittmann Battenfeld provide you with a quote
Supplier
Supplier: Wittmann Battenfeld
Location: Dingley Village , VIC
Is this your product?
Manage products / company details |
Report this product
More from this supplier
Industrial Robot | Sonic Series
Blow Air Chiller
Gravimetric Blender | Gravimax Series
Volumetric Dosing System | Dosimax
Injection Moulding Machine | MicroPower 15 t
Injection Moulding Machine | MacroPower 400 – 2000 t
Injection Moulding Machine | EcoPower 55 – 550 t
Granulator | MAS 2A
Granulator | S-Max Series
Granulator | G- Max 9
You might also like these
Air Cooled Water Chiller | SL-10A | SML
Co2 Glass Laser Chiller CW-5300 | Air Cooled Chiller
Co2 Laser Chillers | 800W Cooling Capacity | Air Cooled Chiller
Air-Cooled Fluid Chiller | Aggreko WCC50
Air-Cooled Fluid Chiller | Aggreko WCC1500
Heat Pump Air-Cooled Fluid Chiller | Aggreko WCH200
Chillers I Quantum Air
Air Cooled Water Chillers IJD 370
Air Cooled Water Chillers IJD 2000
Air Cooled Water Chillers IJD 950
Air Cooled Water Chillers IJD 620
Air Cooled Chillers
Air Cooled Chillers | 155L - EL30003
Air Cooled Chillers | 260L - EL30005
Air Cooled Chiller | Tech Mini
Air Cooled Chiller | LWT
Air Cooled Chiller | TAEevo Tech
Air Cooled Chiller | Aries Tech 2
Air Cooled Chiller | Galaxy Tech
Contact Wittmann Battenfeld
Are you an Air Cooled Chiller supplier?
Reach valuable industrial buyers in minutes
Promote key products & content
Drive cost effective & measurable sales
learn more
Reach valuable industrial buyers in minutes
Promote key products & content
Drive cost effective & measurable sales