Measurement Clamp on Current Probe - P50 ...

Measurement Clamp on Current Probe - P50 1000A

Supplier: Beijing GFUVE Electronics Co.,Ltd.

The round jaw design on the Measurement Clamp P50 Series AC current probes along with the high content nickel metal core makes them well suited for power quality applications where high accuracy and low phase shift along with wide frequency are important.

23 Recent Views Call for more details

The P50 Measurement Clamp is a general purpose 1000A AC current probe designed for use with DMMs, loggers and other instruments that have a current input. It has a 1000:1 ratio and output of 1mA per amp or 1mV per amp measured in the jaw. The P50 has an integral 2.5m lead terminated. The rounded jaw design on this probe makes it well-suited for power applications where high accuracy 0.1% and low phase shift and wide frequency response are important.

Applications

Power quality measuring
Large industrial loads
Measuring around cable bundles
Power load monitoring
Waveform analysis
Energy meter calibrator
Measurement range is 1mA to 1200A

Features

Measurement range of 1mA to 1200A AC
Large jaw opening accommodates conductors up to two 500kcmil
Improved ergonomic design and easy operation
High content nickel metal core
Conforms to EN 61010, 600V CAT III
Low phase shift for power measurement
Designed for DMMs, recorders, loggers, oscilloscopes, power and harmonic meters
UL, CE mark

Parameters

Electrical parameters
Ratio		1000: 1 or 2000:1 (customized)
Accuracy class		0.1%, 0.2%, 0.5%
Primary current		0 - 1000A AC
Secondary current		1mV/A AC, 5mV/A or (customized)
Max. Cont. Input current		1200A
Over voltage category		CAT III 600V
Output signal (AC current)		333mV, 500mV,1V,2V,5V AC at nominal input current
AC Accuracy(1000A Range)
0-10A		0.5%
10-100		0.2%
10-1200A		0.1%
AC Phase Shift(1000A Range)
0-10A		0.5 degree
10-100		0.2 degree
10-1200A		0.1 degree
Frequency range		40Hz-2000Hz
Dielectric strength		3KV 50Hz/60Hz at 1 minute
Temperature range		-20 C to +55 C
Output		2.5 meter cable with D01 connector
Max. voltage not insulated conductors		600 V
Standard		EN 61010-1, EN 61010-2-032, IEC60044-1
Installation		Clamp type
Output mode		Lead output (2.5m)
Mechanical parameters
Dimensions (L x W x H)(mm)		102.9 x 219.6 x 28
Weight (g)		550
Holding wire diameter (mm)		50
Max. jaw opening (mm)		50
Color		Gray or blue
Material		PC+ABS+Polycarbonate, UL94 V0

To contact Beijing GFUVE Electronics Co.,Ltd. about Measurement Clamp on Current Probe - P50 1000A use Get a quote.

Applications

Power quality measuring
Large industrial loads
Measuring around cable bundles
Power load monitoring
Waveform analysis
Energy meter calibrator
Measurement range is 1mA to 1200A

Features

Measurement range of 1mA to 1200A AC
Large jaw opening accommodates conductors up to two 500kcmil
Improved ergonomic design and easy operation
High content nickel metal core
Conforms to EN 61010, 600V CAT III
Low phase shift for power measurement
Designed for DMMs, recorders, loggers, oscilloscopes, power and harmonic meters
UL, CE mark

Parameters

Electrical parameters
Ratio		1000: 1 or 2000:1 (customized)
Accuracy class		0.1%, 0.2%, 0.5%
Primary current		0 - 1000A AC
Secondary current		1mV/A AC, 5mV/A or (customized)
Max. Cont. Input current		1200A
Over voltage category		CAT III 600V
Output signal (AC current)		333mV, 500mV,1V,2V,5V AC at nominal input current
AC Accuracy(1000A Range)
0-10A		0.5%
10-100		0.2%
10-1200A		0.1%
AC Phase Shift(1000A Range)
0-10A		0.5 degree
10-100		0.2 degree
10-1200A		0.1 degree
Frequency range		40Hz-2000Hz
Dielectric strength		3KV 50Hz/60Hz at 1 minute
Temperature range		-20 C to +55 C
Output		2.5 meter cable with D01 connector
Max. voltage not insulated conductors		600 V
Standard		EN 61010-1, EN 61010-2-032, IEC60044-1
Installation		Clamp type
Output mode		Lead output (2.5m)
Mechanical parameters
Dimensions (L x W x H)(mm)		102.9 x 219.6 x 28
Weight (g)		550
Holding wire diameter (mm)		50
Max. jaw opening (mm)		50
Color		Gray or blue
Material		PC+ABS+Polycarbonate, UL94 V0