Heavy Duty High Load Truss Boot
Heavy Duty High Load Truss Boot
Modified Heavy Load Truss Boot to assist in the tie down of trusses in high wind uplift areas. The extra clip dramatically improves the tie down value.
Heavy Duty High Load Truss Boot
Application
- Place the Heavy Duty High Load Truss Boot oin the correct position and drill holes into the bottom chord of the girder truss to suit M16 bolts
- Align the bolt holes of the Heavy Duty High Load Truss Boot to the holes in the girder truss and install the M16 bolts with the correct size washers.
- Place the supported truss on the bracket and drill holes in the supported truss to suit M16 bolts
- Align the bolt holes of the Heavy Duty High Load Truss Boot to the bolt holes in the supported truss and install the M16 bolts with the correct size washers.
- Tighten all bolts before loading with roof materials.
- Drill the hole into the supported truss to suit the recommended bolt size. This hole must align with the bolt hole provided in the truss boot.
- Timber wedge to be fitted between clip and top of supported truss.
- Clip to be placed over the supported truss and bolted into position.
To contact Multinail Australia about Heavy Duty High Load Truss Boot use Get a quote.
Heavy Duty High Load Truss Boot
Application
- Place the Heavy Duty High Load Truss Boot oin the correct position and drill holes into the bottom chord of the girder truss to suit M16 bolts
- Align the bolt holes of the Heavy Duty High Load Truss Boot to the holes in the girder truss and install the M16 bolts with the correct size washers.
- Place the supported truss on the bracket and drill holes in the supported truss to suit M16 bolts
- Align the bolt holes of the Heavy Duty High Load Truss Boot to the bolt holes in the supported truss and install the M16 bolts with the correct size washers.
- Tighten all bolts before loading with roof materials.
- Drill the hole into the supported truss to suit the recommended bolt size. This hole must align with the bolt hole provided in the truss boot.
- Timber wedge to be fitted between clip and top of supported truss.
- Clip to be placed over the supported truss and bolted into position.
To contact Multinail Australia about Heavy Duty High Load Truss Boot use Get a quote.
The Heavy Duty High Load Truss Boot is a bracket used to tie down trusses where wind uplift is high. Its added clip increases the tie-down value by fitting over the supported truss and bolting into place. For connecting a supported truss to a girder truss, it uses bolted connections through both members, with a timber wedge between the clip and the supported truss.
- M16 bolts fasten the boot to the girder truss’s bottom chord
- Drill supported-truss holes to the recommended bolt size
- Use correctly sized washers with the M16 bolts
- Align drilled truss holes with the boot’s bolt holes
- Tighten all bolts before placing roof materials
Source: listing by Multinail Australia on IndustrySearch · Updated 3 Nov 2026
AI Overview is generated by artificial intelligence and may contain mistakes.
Written by AI from the listing by Multinail Australia on IndustrySearch. It is meant to use only what that listing says, but it can still get details wrong, so check them with the supplier before you buy.
Thanks for your feedback.
Roof Truss System | Randek AutoEyeTruss System – SF022
Steel Truss Bracket
Anti-Twist Truss Boot
Universal High Load Truss Boot
Fabricated Trusses
Span Trusses | Pryda
Floor Truss System | Pryda Longreach Trusses
Building Products | NBS Frame Truss
F14 Square 0.3m Linear Truss with Spigots, Pins & R-Clips
F34 Square Truss 6 Way Cube Junction with Half-Spigot Connectors
F34 Square 3.0m Linear Truss with Spigots, Pins & R-Clips
Verto Truss - 0.50m
Boxcorner for Verto Truss
Cantilever Racking System I Truss System
Reach valuable industrial buyers in minutes
Promote key products & content
Drive cost effective & measurable sales